Land Well Service 3512E Dynamic Gas Blending dual fuel Engine

The new land well service 3512E Dynamic Gas Blendingâ„¢ dual fuel engine will be certified to U.S. EPA Tier 4 Final emissions standard while offering the highest natural gas substitution in its class. The 3512E DGB will include factory solutions that emit approximately the same or less greenhouse gas (GHG) emissions as a comparable 3512E Tier 4 Final diesel engine. Additionally, the dual fuel performance of the new 3512E DGB has significantly increased compared to similar engines in its class with the ability to achieve 85% diesel displacement, further allowing for lower operating costs.

Specifications

General Specifications

Maximum Rating
2500BHP
Displacement
3596in³
Minimum Rating
2250BHP
Aspiration
SCAC and ATAAC
Flywheel and Flywheel Housing
SAE No. 0
Flywheel Teeth
151
Stroke
8.5in
Bore
6.7in
Governor and Protection
Electronic (ADEMâ„¢ A5) / DGB System (ADEMâ„¢ A6)
Rotation from Flywheel End
Counterclockwise

Emissions

Emissions
U.S. EPA Tier 4 Final

Dimensions

Length
138in
Width
91in
Height
108in
Weight
22352lb

Capacity for Liquids

Lube Oil System - Refill
52gal (US)
Cooling System
52gal (US)

Standard/Optional Features

Standard Equipment:

  • Control System
    • Cat ADEM A6 DGB controls
  • Cooling System
    • Thermostats and housing, jacket and separate circuit water pump, gear-driven centrifugal
    • SCAC/ATAAC system
  • Exhaust System
    • Dual DOC
    • Exhaust manifold, dry, bellows connection
    • Four turbochargers with watercooled bearings
    • Exhaust outlet, dual 10-inch ANSI round flange as part of aftertreatment
  • Flywheels & Flywheel Housing
    • Flywheel, SAE No. 0, 151 teeth
  • Fuel System
    • Engine mounted Gas filter, water coalescing type
    • Clean fuel module boost pump
    • Fuel transfer pump
    • Common rail fuel system
    • Primary/secondary fuel filters
    • Fuel priming pump (electric)
  • Instrumentation
    • Product LinkTM engine monitoring
  • General
    • Vibration damper and guard
    • Lifting eyes
    • Paint - Caterpillar yellow
  • Lube System
    • Closed Crankcase ventillation - top mounted
    • Fumes disposal
    • Oil filter - RH spin-on type
    • Oil cooler
    • Oil filler and dipstick - LH
    • Oil scavenger pump
    • Oil pump
    • Oil pan drain valve, 1" NPT female connection
  • Mounting System
    • Trunion front support
    • Flywheel housing - two-sidedfailure options
  • Protection System
    • Emergency stop logic inputs provided at 70-pin customer interface connection
    • ADEM A5 and A6 ECU system to provide customer programmable engine deration strategies to protect against adverse operating conditions
  • Aftertreatment Mounting
    • CEM/muffler support package Heavy-duty air cleaners (2 element with precleaners)

Optional Equipment:

  • Charging System
    • 80, 95, or 150 amp charging alternator
  • Control System
    • Local speed throttle control
    • Throttle position sensors
  • Cooling System
    • Coolant conditioner
    • JW outlet coupling-style connections
    • JW inlet weld-flange connection
    • SCAC/ATAAC inlet and outlet coupling-style connections
    • JW inlet and outlet hose barb connections
    • SCAC/ATAAC inlet and outlet hose barb connections Water level switch gauge
    • JW Heater installation connections
  • Exhaust System
    • Flex pipe kit
    • Residential mufflers (painted steel and stainless steel) with outlet elbow and rain cap
  • Flywheels & Flywheel Housing
    • Allison and Twin Disc flywheel options
  • Instrumentation
    • Product Link harness extensions
    • LAN adapters
  • Lube System
    • Rear sump oil pan - 250-hour change interval
    • Front deep sump oil pan - 500-hour change interval
  • Power Take-offs
    • Front Crankshaft Adapter
    • Front crankshaft stub shaft
    • Accessory drive - upper RH
  • Protection System
    • Hydraulic actuated air shutoff
  • Starting System
    • Dual hydraulic starter - LH
    • Manual engine barring device
    • Hydraulic starter - LH
    • EIRS automatic start/stop system is available on factory orders as an attachment
  • Transmission Attachments
    • Transmission oil cooler
    • Transmission oil cooler 2-1 connections
    • Torque converter connections
  • General
    • Air compressor
  • Charging System
    • 80, 95, or 150 amp charging alternator
  • Control System
    • Local speed throttle control
    • Throttle position sensors
  • Cooling System
    • Coolant conditioner
    • JW outlet coupling-style connections
    • JW inlet weld-flange connection
    • SCAC/ATAAC inlet and outlet coupling-style connections
    • JW inlet and outlet hose barb connections
    • SCAC/ATAAC inlet and outlet hose barb connections Water level switch gauge
    • JW Heater installation connections
  • Exhaust System
    • Flex pipe kit
    • Residential mufflers (painted steel and stainless steel) with outlet elbow and rain cap
  • Flywheels & Flywheel Housing
    • Allison and Twin Disc flywheel options
  • Instrumentation
    • Product Link harness extensions
    • LAN adapters
  • Lube System
    • Rear sump oil pan - 250-hour change interval
    • Front deep sump oil pan - 500-hour change interval
  • Power Take-offs
    • Front Crankshaft Adapter
    • Front crankshaft stub shaft
    • Accessory drive - upper RH
  • Protection System
    • Hydraulic actuated air shutoff
  • Starting System
    • Dual hydraulic starter - LH
    • Manual engine barring device
    • Hydraulic starter - LH
    • EIRS automatic start/stop system is available on factory orders as an attachment
  • Transmission Attachments
    • Transmission oil cooler
    • Transmission oil cooler 2-1 connections
    • Torque converter connections
  • General
    • Air compressor
  • Charging System
    • 80, 95, or 150 amp charging alternator
  • Control System
    • Local speed throttle control
    • Throttle position sensors
  • Cooling System
    • Coolant conditioner
    • JW outlet coupling-style connections
    • JW inlet weld-flange connection
    • SCAC/ATAAC inlet and outlet coupling-style connections
    • JW inlet and outlet hose barb connections
    • SCAC/ATAAC inlet and outlet hose barb connections Water level switch gauge
    • JW Heater installation connections
  • Exhaust System
    • Flex pipe kit
    • Residential mufflers (painted steel and stainless steel) with outlet elbow and rain cap
  • Flywheels & Flywheel Housing
    • Allison and Twin Disc flywheel options
  • Instrumentation
    • Product Link harness extensions
    • LAN adapters
  • Lube System
    • Rear sump oil pan - 250-hour change interval
    • Front deep sump oil pan - 500-hour change interval
  • Power Take-offs
    • Front Crankshaft Adapter
    • Front crankshaft stub shaft
    • Accessory drive - upper RH
  • Protection System
    • Hydraulic actuated air shutoff
  • Starting System
    • Dual hydraulic starter - LH
    • Manual engine barring device
    • Hydraulic starter - LH
    • EIRS automatic start/stop system is available on factory orders as an attachment
  • Transmission Attachments
    • Transmission oil cooler
    • Transmission oil cooler 2-1 connections
    • Torque converter connections
  • General
    • Air compressor
  • Charging System
    • 80, 95, or 150 amp charging alternator
  • Control System
    • Local speed throttle control
    • Throttle position sensors
  • Cooling System
    • Coolant conditioner
    • JW outlet coupling-style connections
    • JW inlet weld-flange connection
    • SCAC/ATAAC inlet and outlet coupling-style connections
    • JW inlet and outlet hose barb connections
    • SCAC/ATAAC inlet and outlet hose barb connections Water level switch gauge
    • JW Heater installation connections
  • Exhaust System
    • Flex pipe kit
    • Residential mufflers (painted steel and stainless steel) with outlet elbow and rain cap
  • Flywheels & Flywheel Housing
    • Allison and Twin Disc flywheel options
  • Instrumentation
    • Product Link harness extensions
    • LAN adapters
  • Lube System
    • Rear sump oil pan - 250-hour change interval
    • Front deep sump oil pan - 500-hour change interval
  • Power Take-offs
    • Front Crankshaft Adapter
    • Front crankshaft stub shaft
    • Accessory drive - upper RH
  • Protection System
    • Hydraulic actuated air shutoff
  • Starting System
    • Dual hydraulic starter - LH
    • Manual engine barring device
    • Hydraulic starter - LH
    • EIRS automatic start/stop system is available on factory orders as an attachment
  • Transmission Attachments
    • Transmission oil cooler
    • Transmission oil cooler 2-1 connections
    • Torque converter connections
  • General
    • Air compressor
  • Charging System
    • 80, 95, or 150 amp charging alternator
  • Control System
    • Local speed throttle control
    • Throttle position sensors
  • Cooling System
    • Coolant conditioner
    • JW outlet coupling-style connections
    • JW inlet weld-flange connection
    • SCAC/ATAAC inlet and outlet coupling-style connections
    • JW inlet and outlet hose barb connections
    • SCAC/ATAAC inlet and outlet hose barb connections Water level switch gauge
    • JW Heater installation connections
  • Exhaust System
    • Flex pipe kit
    • Residential mufflers (painted steel and stainless steel) with outlet elbow and rain cap
  • Flywheels & Flywheel Housing
    • Allison and Twin Disc flywheel options
  • Instrumentation
    • Product Link harness extensions
    • LAN adapters
  • Lube System
    • Rear sump oil pan - 250-hour change interval
    • Front deep sump oil pan - 500-hour change interval
  • Power Take-offs
    • Front Crankshaft Adapter
    • Front crankshaft stub shaft
    • Accessory drive - upper RH
  • Protection System
    • Hydraulic actuated air shutoff
  • Starting System
    • Dual hydraulic starter - LH
    • Manual engine barring device
    • Hydraulic starter - LH
    • EIRS automatic start/stop system is available on factory orders as an attachment
  • Transmission Attachments
    • Transmission oil cooler
    • Transmission oil cooler 2-1 connections
    • Torque converter connections
  • General
    • Air compressor
  • Charging System
    • 80, 95, or 150 amp charging alternator
  • Control System
    • Local speed throttle control
    • Throttle position sensors
  • Cooling System
    • Coolant conditioner
    • JW outlet coupling-style connections
    • JW inlet weld-flange connection
    • SCAC/ATAAC inlet and outlet coupling-style connections
    • JW inlet and outlet hose barb connections
    • SCAC/ATAAC inlet and outlet hose barb connections Water level switch gauge
    • JW Heater installation connections
  • Exhaust System
    • Flex pipe kit
    • Residential mufflers (painted steel and stainless steel) with outlet elbow and rain cap
  • Flywheels & Flywheel Housing
    • Allison and Twin Disc flywheel options
  • Instrumentation
    • Product Link harness extensions
    • LAN adapters
  • Lube System
    • Rear sump oil pan - 250-hour change interval
    • Front deep sump oil pan - 500-hour change interval
  • Power Take-offs
    • Front Crankshaft Adapter
    • Front crankshaft stub shaft
    • Accessory drive - upper RH
  • Protection System
    • Hydraulic actuated air shutoff
  • Starting System
    • Dual hydraulic starter - LH
    • Manual engine barring device
    • Hydraulic starter - LH
    • EIRS automatic start/stop system is available on factory orders as an attachment
  • Transmission Attachments
    • Transmission oil cooler
    • Transmission oil cooler 2-1 connections
    • Torque converter connections
  • General
    • Air compressor
  • Charging System
    • 80, 95, or 150 amp charging alternator
  • Control System
    • Local speed throttle control
    • Throttle position sensors
  • Cooling System
    • Coolant conditioner
    • JW outlet coupling-style connections
    • JW inlet weld-flange connection
    • SCAC/ATAAC inlet and outlet coupling-style connections
    • JW inlet and outlet hose barb connections
    • SCAC/ATAAC inlet and outlet hose barb connections Water level switch gauge
    • JW Heater installation connections
  • Exhaust System
    • Flex pipe kit
    • Residential mufflers (painted steel and stainless steel) with outlet elbow and rain cap
  • Flywheels & Flywheel Housing
    • Allison and Twin Disc flywheel options
  • Instrumentation
    • Product Link harness extensions
    • LAN adapters
  • Lube System
    • Rear sump oil pan - 250-hour change interval
    • Front deep sump oil pan - 500-hour change interval
  • Power Take-offs
    • Front Crankshaft Adapter
    • Front crankshaft stub shaft
    • Accessory drive - upper RH
  • Protection System
    • Hydraulic actuated air shutoff
  • Starting System
    • Dual hydraulic starter - LH
    • Manual engine barring device
    • Hydraulic starter - LH
    • EIRS automatic start/stop system is available on factory orders as an attachment
  • Transmission Attachments
    • Transmission oil cooler
    • Transmission oil cooler 2-1 connections
    • Torque converter connections
  • General
    • Air compressor
  • Charging System
    • 80, 95, or 150 amp charging alternator
  • Control System
    • Local speed throttle control
    • Throttle position sensors
  • Cooling System
    • Coolant conditioner
    • JW outlet coupling-style connections
    • JW inlet weld-flange connection
    • SCAC/ATAAC inlet and outlet coupling-style connections
    • JW inlet and outlet hose barb connections
    • SCAC/ATAAC inlet and outlet hose barb connections Water level switch gauge
    • JW Heater installation connections
  • Exhaust System
    • Flex pipe kit
    • Residential mufflers (painted steel and stainless steel) with outlet elbow and rain cap
  • Flywheels & Flywheel Housing
    • Allison and Twin Disc flywheel options
  • Instrumentation
    • Product Link harness extensions
    • LAN adapters
  • Lube System
    • Rear sump oil pan - 250-hour change interval
    • Front deep sump oil pan - 500-hour change interval
  • Power Take-offs
    • Front Crankshaft Adapter
    • Front crankshaft stub shaft
    • Accessory drive - upper RH
  • Protection System
    • Hydraulic actuated air shutoff
  • Starting System
    • Dual hydraulic starter - LH
    • Manual engine barring device
    • Hydraulic starter - LH
    • EIRS automatic start/stop system is available on factory orders as an attachment
  • Transmission Attachments
    • Transmission oil cooler
    • Transmission oil cooler 2-1 connections
    • Torque converter connections
  • General
    • Air compressor
  • Charging System
    • 80, 95, or 150 amp charging alternator
  • Control System
    • Local speed throttle control
    • Throttle position sensors
  • Cooling System
    • Coolant conditioner
    • JW outlet coupling-style connections
    • JW inlet weld-flange connection
    • SCAC/ATAAC inlet and outlet coupling-style connections
    • JW inlet and outlet hose barb connections
    • SCAC/ATAAC inlet and outlet hose barb connections Water level switch gauge
    • JW Heater installation connections
  • Exhaust System
    • Flex pipe kit
    • Residential mufflers (painted steel and stainless steel) with outlet elbow and rain cap
  • Flywheels & Flywheel Housing
    • Allison and Twin Disc flywheel options
  • Instrumentation
    • Product Link harness extensions
    • LAN adapters
  • Lube System
    • Rear sump oil pan - 250-hour change interval
    • Front deep sump oil pan - 500-hour change interval
  • Power Take-offs
    • Front Crankshaft Adapter
    • Front crankshaft stub shaft
    • Accessory drive - upper RH
  • Protection System
    • Hydraulic actuated air shutoff
  • Starting System
    • Dual hydraulic starter - LH
    • Manual engine barring device
    • Hydraulic starter - LH
    • EIRS automatic start/stop system is available on factory orders as an attachment
  • Transmission Attachments
    • Transmission oil cooler
    • Transmission oil cooler 2-1 connections
    • Torque converter connections
  • General
    • Air compressor
  • Charging System
    • 80, 95, or 150 amp charging alternator
  • Control System
    • Local speed throttle control
    • Throttle position sensors
  • Cooling System
    • Coolant conditioner
    • JW outlet coupling-style connections
    • JW inlet weld-flange connection
    • SCAC/ATAAC inlet and outlet coupling-style connections
    • JW inlet and outlet hose barb connections
    • SCAC/ATAAC inlet and outlet hose barb connections Water level switch gauge
    • JW Heater installation connections
  • Exhaust System
    • Flex pipe kit
    • Residential mufflers (painted steel and stainless steel) with outlet elbow and rain cap
  • Flywheels & Flywheel Housing
    • Allison and Twin Disc flywheel options
  • Instrumentation
    • Product Link harness extensions
    • LAN adapters
  • Lube System
    • Rear sump oil pan - 250-hour change interval
    • Front deep sump oil pan - 500-hour change interval
  • Power Take-offs
    • Front Crankshaft Adapter
    • Front crankshaft stub shaft
    • Accessory drive - upper RH
  • Protection System
    • Hydraulic actuated air shutoff
  • Starting System
    • Dual hydraulic starter - LH
    • Manual engine barring device
    • Hydraulic starter - LH
    • EIRS automatic start/stop system is available on factory orders as an attachment
  • Transmission Attachments
    • Transmission oil cooler
    • Transmission oil cooler 2-1 connections
    • Torque converter connections
  • General
    • Air compressor
  • Charging System
    • 80, 95, or 150 amp charging alternator
  • Control System
    • Local speed throttle control
    • Throttle position sensors
  • Cooling System
    • Coolant conditioner
    • JW outlet coupling-style connections
    • JW inlet weld-flange connection
    • SCAC/ATAAC inlet and outlet coupling-style connections
    • JW inlet and outlet hose barb connections
    • SCAC/ATAAC inlet and outlet hose barb connections Water level switch gauge
    • JW Heater installation connections
  • Exhaust System
    • Flex pipe kit
    • Residential mufflers (painted steel and stainless steel) with outlet elbow and rain cap
  • Flywheels & Flywheel Housing
    • Allison and Twin Disc flywheel options
  • Instrumentation
    • Product Link harness extensions
    • LAN adapters
  • Lube System
    • Rear sump oil pan - 250-hour change interval
    • Front deep sump oil pan - 500-hour change interval
  • Power Take-offs
    • Front Crankshaft Adapter
    • Front crankshaft stub shaft
    • Accessory drive - upper RH
  • Protection System
    • Hydraulic actuated air shutoff
  • Starting System
    • Dual hydraulic starter - LH
    • Manual engine barring device
    • Hydraulic starter - LH
    • EIRS automatic start/stop system is available on factory orders as an attachment
  • Transmission Attachments
    • Transmission oil cooler
    • Transmission oil cooler 2-1 connections
    • Torque converter connections
  • General
    • Air compressor

Contact Tractor & Equipment Co. today for all of your equipment needs!

Contact Us